Kullanım kılavuzu Greenworks GD40CS18 Motorlu testere

Kullanım kılavuzu

• The location of larger branches.

•

The wind direction.

• There are no dirt, stones, loose bark, nails, and

staples on the tree.

1. Make a lower level notching cut. Make sure that this

cut is

a) 1/3 wide of the diameter of the tree.

b) Perpendicular to the felling direction.

CAUTION

The level notching cut helps prevent pinching of

the saw chain or the guide bar when you make the

second notch.

2. Make the felling cut no less than 50 mm and higher

than the level notching cut. Make sure that this cut

a) Is parallel to the level notching cut.

b) Keeps sufficient wood to become a hinge which

prevents the tree from twisting and felling to the

wrong direction.

When the felling cut gets near the hinge, the tree

falls. Stop the felling cut if the tree

• Does not fall to the correct direction or

• Move rearward and forward and stuck the chain.

3. Use felling wedge to open the cut and let the tree

fall to the correct direction.

4. When the tree starts to fall,

a) Remove the chainsaw from the cut.

b) Stop the machine.

c) Put the machine down.

d) Go away through the escape path. Be careful

with overhead branches and your footing.

4.7 LIMB A TREE

Figure 11.

Limbing is to remove the branches from a fallen tree.

1. Keep the larger lower branches to hold the log off

the ground.

2. Remove the small limbs in one cut.

3. Limb the branches with tension from the bottom to

up.

4. Keep the larger lower branches as a support until

the log is limbed.

4.8 BUCK A LOG

Figure 12-15.

Bucking is to cut a log into lengths. Keep your body

balance. If it is possible, lift the log and hold it with

branches, logs or chock.

• When the log is held along the full length, cut it from

the top.

• When the log is held on one end,

1.

Cut the first time 1/3 of the diameter from the

bottom.

2. Cut the second time from the top to complete the

bucking.

• When the log is held on two ends,

1. Cut the first time 1/3 of the diameter from the

top.

2. Cut the second time lower 2/3 from the bottom to

complete the bucking.

• When the log is on a slope,

1. Stand on the uphill side.

2. Control the chainsaw.

3. Hold the handles tightly.

4. Release the cut pressure near the end of the

cut.

NOTE

Do not let the chain touch the ground.

When bucking is complete,

1. Release the trigger.

2. Stop the chainsaw fully.

3. Move the chainsaw from tree to tree.

5 MAINTENANCE

CAUTION

Do not let brake fluids, gasoline, petroleum-based

materials touch the plastic parts. Chemicals can cause

damage to the plastic, and make the plastic

unserviceable.

CAUTION

Do not use strong solvents or detergents on the plastic

housing or components.

WARNING

Remove the battery pack from the machine before

maintenance.

5.1 ADJUST THE CHAIN TENSION

Figure 2-7.

The more you use a chain the longer it becomes. It is

therefore important to adjust the chain regularly to take

up the slack.

Tension the chain as tightly as possible, but not so tight

that you cannot pull it round freely by hand.

7

English

EN

Derecelendirme

Bu kılavuz hakkında daha fazla bilgi

Greenworks GD40CS18 Motorlu testere cihazınız için basılı bir kılavuza sahip olmanın güzel bir şey olduğunun farkındayız. Kılavuzu her zaman web sitemizden indirebilir ve kendiniz yazdırabilirsiniz. Orijinal bir kılavuza sahip olmak istiyorsanız Greenworks ile iletişime geçmenizi öneririz. Orijinal bir kılavuz sağlayabilirler. Greenworks GD40CS18 Motorlu testere cihazınızın kılavuzunu farklı bir dilde mi arıyorsunuz? Ana sayfamızdan tercih ettiğiniz dili seçin ve mevcut olup olmadığını görmek için model numarasını arayın.

Özellikler

Greenworks Motorlu testereler için tüm kılavuzlar
Motorlu testereler ile ilgili daha fazla kılavuz

Greenworks GD40CS18 Motorlu testere hakkında Sıkça Sorulan Sorular

Destek ekibimiz faydalı ürün bilgileri arar ve sıkça sorulan soruları cevaplar. Sıkça sorulan sorularda hatalı bir cevaba rastlamanız halinde lütfen bunu iletişim formunu kullanarak bize bildirin.

İlgili ürünler

Kullanım kılavuzu

Greenworks GD24CS30 Motorlu testere

Kullanım kılavuzu

Greenworks CD40CS15 Motorlu testere

Kullanım kılavuzu

Greenworks GD60CS40 Motorlu testere

Kullanım kılavuzu

Greenworks GD40TCS Motorlu testere

Kullanım kılavuzu

Makita DUC101 Motorlu testere

Kullanım kılavuzu

Güde KS 401 E Motorlu testere

Kullanım kılavuzu

AL-KO BKS 2625 TSB Motorlu testere

Kullanım kılavuzu

EGO CS2000E Motorlu testere

İlgili kategoriler