Kullanım kılavuzu Hitachi G 10SD2 Avuç taşlama makinesi

Kullanım kılavuzu

5

English

7. The wheel continues to rotate after the tool is switched

off .

After switching off the machine, do not put it down until

the depressed center wheel has come to a complete

stop. Apart from avoiding serious accidents, this

precaution will reduce the amount of dust and swarf

sucked into the machine.

8. When the machine is not use, the power source should

be disconnected.

9. Be sure to switch OFF and disconnect the attachment

plug from the receptacle to avoid a serious accident

before the depressed center wheel is assembling and

disassembling.

10. RCD

The use of a residual current device with a rated residual

current of 30 mA or less at all times is recommended.

SYMBOLS

WARNING

The following show symbols used for the machine.

Be sure that you understand their meaning before

use.

G10SD2 / G12S2 / G13SD: Disc Grinder

Read all safety warnings and all instructions.

Always wear eye protection.

Only for EU countries

Do not dispose of electric tools together with

household waste material!

In observance of European Directive 2002/96/

EC on waste electrical and electronic equipment

and its implementation in accordance with

national law, electric tools that have reached

the end of their life must be collected separately

and returned to an environmentally compatible

recycling facility.

V Rated voltage

Alternating current

P

Power input

n

Rated speed

min

-1

Revolution or reciprocations per minute

D Wheel outer diameter

d Wheel hole diameter

t Wheel thickness

Peripheral speed

kg

Weight (Only main body)

Ϩ

Switching ON

Switching OFF

Disconnect mains plug from electrical outlet

Warning

Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package

contains the accessories listed in the below.

○ Wrench .........................................................................1

○ Side handle ...................................................................1

○ Depressed center wheel ...............................................1

Standard accessories are subject to change without notice.

APPLICATIONS

○ Removal of casting fi n and fi nishing of various types of

steel, bronze and aluminum materials and castings.

○ Grinding of welded sections or sections cut by means of

a cutting torch.

○ Grinding of synthetic resins, slate, brick, marble, etc.

○ Cutting of synthetic concrete, stone, brick, marble, and

similar materials.

SPECIFICATIONS

The specifi cations of this machine are listed in the Table on

page 134.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifi cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Fitting and adjusting the wheel guard 1 135

Fixing the side handle 2 135

Assembling depressed center wheel 3 135

Assembling cutting wheel 4 135

Switch operation 5 136

Grinding angle and grinding method 6 136

Replacing carbon brushes 7 136

Selecting accessories ― 137

MAINTENANCE AND INSPECTION

1. Inspecting the depressed center wheel

Ensure that the depressed center wheel is free of cracks

and surface defects.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Inspecting the carbon brushes (Fig. 7)

The motor employs carbon brushes which are

consumable parts. Since an excessively worn carbon

brush can result in motor trouble, replace the carbon

brushes with new ones having the same carbon brush

No. ⓐ shown in the fi gure when it becomes worn to or

near the “wear limit” ⓑ. In addition, always keep carbon

brushes clean and ensue that they slide freely within the

brush holders.

4. Replacing carbon brushes (Fig. 7)

⟨Disassembly⟩

(1) Loosen the D4 tapping screw ⓒ retaining the tail cover

ⓓ and remove the tail cover.

0000Book̲G10SD2.indb50000Book̲G10SD2.indb5 2014/10/319:11:462014/10/319:11:46

Derecelendirme

Bu kılavuz hakkında daha fazla bilgi

Hitachi G 10SD2 Avuç taşlama makinesi cihazınız için basılı bir kılavuza sahip olmanın güzel bir şey olduğunun farkındayız. Kılavuzu her zaman web sitemizden indirebilir ve kendiniz yazdırabilirsiniz. Orijinal bir kılavuza sahip olmak istiyorsanız Hitachi ile iletişime geçmenizi öneririz. Orijinal bir kılavuz sağlayabilirler. Hitachi G 10SD2 Avuç taşlama makinesi cihazınızın kılavuzunu farklı bir dilde mi arıyorsunuz? Ana sayfamızdan tercih ettiğiniz dili seçin ve mevcut olup olmadığını görmek için model numarasını arayın.

Özellikler

Hitachi Avuç taşlama makineleri için tüm kılavuzlar
Avuç taşlama makineleri ile ilgili daha fazla kılavuz

Hitachi G 10SD2 Avuç taşlama makinesi hakkında Sıkça Sorulan Sorular

Destek ekibimiz faydalı ürün bilgileri arar ve sıkça sorulan soruları cevaplar. Sıkça sorulan sorularda hatalı bir cevaba rastlamanız halinde lütfen bunu iletişim formunu kullanarak bize bildirin.

İlgili ürünler

Kullanım kılavuzu

Hitachi G 18UC Avuç taşlama makinesi

Kullanım kılavuzu

Hitachi G 18SH2 Avuç taşlama makinesi

Kullanım kılavuzu

Einhell TC-AG 115/750 Avuç taşlama makinesi

Kullanım kılavuzu

Bosch GWX 19-125 S Avuç taşlama makinesi

Kullanım kılavuzu

Stayer FH 700 B Avuç taşlama makinesi

Kullanım kılavuzu

Stayer SAB 1601 CS Avuç taşlama makinesi

Kullanım kılavuzu

Bosch GWX 18V-8 Avuç taşlama makinesi

Kullanım kılavuzu

Einhell TP-AG 18/125 CE Q Li-Solo Avuç taşlama makinesi

İlgili kategoriler