Kullanım kılavuzu Makita JR102D Tilki kuyruğu testere

Kullanım kılavuzu

7

Pull the switch lever/trigger to light up the lamp. The lamp

keeps on lighting while the switch lever/trigger is being

pulled.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing the saw blade

CAUTION:

• Always clean out all chips or foreign matter adhering to

the blade, blade clamp and/or slider. Failure to do so

may cause insufficient tightening of the blade, resulting

in a serious injury.

For Model JR100D (Fig. 4)

Insert the recipro saw blade into the blade clamp as far as

it will go. The blade clamp sleeve rotates and the saw

blade is fixed. Make sure that the saw blade cannot be

extracted even though you try to pull it out.

CAUTION:

• If you do not insert the saw blade deep enough, the

saw blade may be ejected unexpectedly during

operation. This can be extremely dangerous.

NOTE:

• You can not use the jig saw blade with JR100D.

(Fig. 5)

To remove the saw blade, rotate the blade clamp sleeve

in the direction of the arrow fully. The saw blade is

removed and the blade clamp sleeve is fixed at the

released position.

NOTE:

• If you remove the saw blade without rotating the blade

clamp sleeve fully, the sleeve may not be fixed. In this

case, rotate the blade clamp sleeve fully, then make

the sleeve fixed at the released position.

For Model JR102D

To install the saw blade, loosen the bolt by hex wrench.

When installing a recipro saw blade, press the bolt with

the hex wrench to open the slot during inserting the blade.

(Fig. 6 & 7)

You can use both jig saw blades (B type) and recipro saw

blades according to your work. Insert the saw blade

straight into the blade clamp and tighten it by hex wrench.

Pull the saw blade lightly to make sure that the saw blade

does not fall off during operation.

To remove the saw blade, follow the installation

procedure in reverse. (Fig. 8 & 9)

Hex wrench storage (Fig. 10)

When not in use, store the hex wrench. It is fixed by two

projections as shown in the figure to keep it from being

lost.

OPERATION (Fig. 11)

CAUTION:

• Always press the shoe firmly against the workpiece

during operation. If the shoe is held away from the

workpiece during operation, strong vibration and/or

twisting will be produced, causing the blade to snap

dangerously.

• Always wear gloves to protect your hands from hot

flying chips when cutting metal.

• Be sure to always wear suitable eye protection which

conforms with current national standards.

• Always use a suitable coolant (cutting oil) when cutting

metal. Failure to do so will cause premature blade

wear.

Press the shoe firmly against the workpiece. Do not allow

the tool to bounce. Bring the saw blade into light contact

with the workpiece. First, make a pilot groove using a

slower speed. Then use a faster speed to continue

cutting. (Fig. 12 & 13)

• You can use the switch lever or trigger according to

your work.

NOTE:

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Recipro saw blades

• Jig saw blades (only for Model JR102D)

• Various type of Makita genuine batteries and chargers

• Plastic carrying case

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Model JR100D

Sound pressure level (L

pA

): 78 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Derecelendirme

Bu kılavuz hakkında daha fazla bilgi

Makita JR102D Tilki kuyruğu testere cihazınız için basılı bir kılavuza sahip olmanın güzel bir şey olduğunun farkındayız. Kılavuzu her zaman web sitemizden indirebilir ve kendiniz yazdırabilirsiniz. Orijinal bir kılavuza sahip olmak istiyorsanız Makita ile iletişime geçmenizi öneririz. Orijinal bir kılavuz sağlayabilirler. Makita JR102D Tilki kuyruğu testere cihazınızın kılavuzunu farklı bir dilde mi arıyorsunuz? Ana sayfamızdan tercih ettiğiniz dili seçin ve mevcut olup olmadığını görmek için model numarasını arayın.

Özellikler

Makita Tilki kuyruğu testereler için tüm kılavuzlar
Tilki kuyruğu testereler ile ilgili daha fazla kılavuz

Makita JR102D Tilki kuyruğu testere hakkında Sıkça Sorulan Sorular

Destek ekibimiz faydalı ürün bilgileri arar ve sıkça sorulan soruları cevaplar. Sıkça sorulan sorularda hatalı bir cevaba rastlamanız halinde lütfen bunu iletişim formunu kullanarak bize bildirin.

İlgili ürünler

Kullanım kılavuzu

Makita DJR145 Tilki kuyruğu testere

Kullanım kılavuzu

Makita DJR143 Tilki kuyruğu testere

Kullanım kılavuzu

Makita JR100D Tilki kuyruğu testere

Kullanım kılavuzu

Makita DJR185 Tilki kuyruğu testere

Kullanım kılavuzu

Makita DJR187ZK Tilki kuyruğu testere

Kullanım kılavuzu

Makita DJR183 Tilki kuyruğu testere

Kullanım kılavuzu

Makita DJR360ZK Tilki kuyruğu testere

Kullanım kılavuzu

Einhell GE-GS 18/150 Li-Solo Tilki kuyruğu testere

İlgili kategoriler