Kullanım kılavuzu Bosch AXT 2500 HP Bahçe öğütücüsü

Kullanım kılavuzu

English - 4

Thick branches are not pulled in:

■ Check cutting roller 13: If heavily worn, it must be

replaced.

Shredded material is not completely separated

and hangs together as a chain:

■ Adjust pressure plate 12 (according to Section

“Pressure Plate Adjustment”).

■ If the pressure plate 12 can no longer be ad-

justed, it must be replaced.

The motor does not run:

■ The overload protection has tripped: Allow the

motor to cool. Place rotational direction switch 2

in the left position (backwards) and switch on the

machine again. Allow the blockage clear. Then

switch off and switch the rotational direction back

to “right”.

Check the house fuse. The circuit must be pro-

tected with at least the following fuse sizes:

AXT 2200 HP = 10 A, AXT 2500 HP = 16 A.

Direction of rotation switches automatically:

■ When the machine is suddenly blocked (e. g. be-

cause of a large branch), the direction of rotation

of the cutting roller switches automatically. In this

case switch the machine off, wait until it stops and

switch it on again.

– Place rotational direction switch 2 in the left posi-

tion, switch machine on. The cutting roller 13 runs

backwards and releases the shredded material

(or foreign material). A special gear construction

with rotational angle play allows the motor to start

in the opposite rotational direction even if the cut-

ting roller 13 is blocked. In extreme cases loosen

pressure plate 12 (anti clockwise) before switch-

ing the machine on backwards.

– When the caught material is free, switch off ma-

chine, set rotational direction switch 2 to the right

position and switch back on. Readjust the pres-

sure plate if necessary.

– If the blocking cannot be eliminated by actions 1

and 2, the cutting roller 13 must be removed,

checked for damage, and cleaned as described

in section “Exchanging the Cutting Roller/Pres-

sure Plate”.

■ Before any work on the machine itself, re-

move plug from the mains supply.

☞

For safe and proper working, always keep the

machine and the ventilation slots clean.

The shredder must not be cleaned with high-pres-

sure cleaners or running water.

The tightness of the fastening screws of the under-

carriage should be checked from time to time.

The cutting roller 13 and the pressure plate 12 have

a life expectancy of several years under normal us-

age and when adjustment according to instructions.

Before storing the machine, remove the cutting roller

(as described in the Section “Replacing the Cutting

Roller/Pressure Plate”) and clean. Then treat the

cutting roller with preservation spray (Accessory, Or-

der No. 1 609 200 399) and grease the bearings.

If the machine should happen to fail despite the care

taken in manufacture and testing, repair is to be car-

ried out by an authorised after-sales service agent.

For all correspondence and spare parts orders, al-

ways include the 10-digit part number (typ) from the

nameplate of the machine!

■ Before any work on the machine itself, re-

move plug from the mains supply.

– Disassemble the cutting roller 13/pressure

plate 12, sequence ➀ – ➄.

– Clean the cutting roller 13.

– Clean and grease the bearings.

– Reassemble the individual parts in the

sequence ➄ – ➀.

– Afterwards turn adjustment knob 8 to the right un-

til a light grinding sound can be heard and some

small aluminium shavings fall out of the ejection

chute 6. In case of stiffness of the adjustment

knob 8, e. g. due to dirt, loosen it with aid of the

Allen key 7.

The following exchangeable parts are available:

Pressure plate ................... Part No. 1 601 000 001

When transporting without the stand, always use the

transport safety 14 piece!

Cutting Roller is blocked

Maintenance and storage

Removing the Cutting Roller/

Pressure Plate (see figure )

Transport Protection

(see figure )

G

H

F016 L70 439 - book.book Seite 4 Dienstag, 28. Februar 2006 7:57 07

14 • F016 L70 439 • TMS • 06.02

Derecelendirme

Bu kılavuz hakkında daha fazla bilgi

Bosch AXT 2500 HP Bahçe öğütücüsü cihazınız için basılı bir kılavuza sahip olmanın güzel bir şey olduğunun farkındayız. Kılavuzu her zaman web sitemizden indirebilir ve kendiniz yazdırabilirsiniz. Orijinal bir kılavuza sahip olmak istiyorsanız Bosch ile iletişime geçmenizi öneririz. Orijinal bir kılavuz sağlayabilirler. Bosch AXT 2500 HP Bahçe öğütücüsü cihazınızın kılavuzunu farklı bir dilde mi arıyorsunuz? Ana sayfamızdan tercih ettiğiniz dili seçin ve mevcut olup olmadığını görmek için model numarasını arayın.

Özellikler

Bosch Bahçe öğütücüleri için tüm kılavuzlar
Bahçe öğütücüleri ile ilgili daha fazla kılavuz

Bosch AXT 2500 HP Bahçe öğütücüsü hakkında Sıkça Sorulan Sorular

Destek ekibimiz faydalı ürün bilgileri arar ve sıkça sorulan soruları cevaplar. Sıkça sorulan sorularda hatalı bir cevaba rastlamanız halinde lütfen bunu iletişim formunu kullanarak bize bildirin.

İlgili ürünler

Kullanım kılavuzu

Bosch AXT Rapid 180 Bahçe öğütücüsü

Kullanım kılavuzu

Bosch AXT Rapid 200 Bahçe öğütücüsü

Kullanım kılavuzu

Bosch AXT 2000 HP Bahçe öğütücüsü

Kullanım kılavuzu

Bosch AXT 25 TC Bahçe öğütücüsü

Kullanım kılavuzu

Bosch AXT 2200 HP Bahçe öğütücüsü

Kullanım kılavuzu

Bosch AXT 1600 HP Bahçe öğütücüsü

Kullanım kılavuzu

Bosch AXT Rapid 2200 Bahçe öğütücüsü

Kullanım kılavuzu

Bosch AXT 25 D Bahçe öğütücüsü

İlgili kategoriler